Flow Sensor G1/2'' Water Flow Hall Sensor Switch 1-25L/min Flow Meter Flowmeter

Description

Visit store
Items for sale
About us
Product Details
Product Description:
1. This product is light and handy in appearance, small in size, and easy to install.
2.The impeller is inlaid with stainless steel beads, which is permanent and wear-resistant.
3.The sealing ring adopts the structure of upper and lower force and never leaks.
4. The Hall element is imported with original packaging and is encapsulated with potting glue to prevent water ingress and never age.
5. Wide application scenarios, widely used in water heaters, drinking fountains, water vending machines, campus credit card machines
Main parameters:
The water flow sensor is mainly composed of a plastic valve body, a water flow rotor assembly and a Hall sensor. It is installed at the water inlet end of the water heater to detect the water flow rate. When the water passes through the water flow rotor assembly, the magnetic rotor rotates and the speed changes with the flow rate. The Hall sensor outputs the corresponding pulse signal and feeds it back to the controller. The device judges the size of the water flow and regulates it.
Interface size: 4 points (G1/2)
Working voltage range: DC5～18V
Inner diameter/outer diameter: inner diameter water inlet 15.4, water outlet 13.5mm/ outer diameter 20.5mm
Thread length: 9.3mm
Water pressure resistance: ≤1.75MPa
Output pulse high level: >DC4.7V (input voltage DC 5V)
Output pulse duty cycle: 50%±10%
Insulation resistance: >100MΩ
Flow range: (at 1～25L\MIN) ±3%
Tightness: Close each hole, add 1.7Mpa water pressure test for 1 minute, no leakage and deformation
Pulse frequency: (Hz)=[ 11*Q ]±5%(Q--Flow L/min)
Wiring mode:
Red IN is connected to the positive pole
Yellow OUT signal output line
Black GND connect to negative pole
Matters needing attention:
1. Severe impact and chemical erosion are strictly prohibited
2. Throwing or collision is strictly prohibited
3. Vertical installation, the inclination does not exceed 5 degrees
4. The temperature of the medium should not exceed 120℃
Package List:
1x Flow sensor
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.